tss.mi-conclu.cto'i ^pioducti, dnc. telephone: (973) 376-2922 (212) 227-6005 fax: (973) 376-8960 20 stern ave. springfield, new jersey 07081 u.s.a. transzorb? transient voltage suppressors icte5 thru icte18c, 1N6373 thru 1n6386 features ? glass passivated chip junction ? available in uni-directional and bi-directional ? 1500 w peak pulse power capability with a 10/1000 u.s waveform, repetitive rate (duty cycle): 0.01 % ? excellent clamping capability ? very fast response time ? low incremental surge resistance ? solder dip 275 c max. 10 s, per jesd 22-b106 ? aec-q101 qualified primary characteristics vwm pppm pd 'fsm tj max. 5.0 v to 18v 1500w 6.5 w 200 a 175c devices for bi-direction applications for bi-directional types, use c suffix (e.g. icte18c). electrical characteristics apply in both directions. typical applications use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ics, mosfet, signal lines of sensor units for consumer, computer, industrial and telecommunication. mechanical data case: molded epoxy body over passivated junction molding compound meets ul 94 v-0 flammability rating terminals: matte tin plated leads, solderable per j-std-002 and jesd 22-b102 e3 suffix meets jesd 201 class 1a whisker test, he3 suffix meets jesd 201 class 2 whisker test polarity: for uni-directional types the color band denotes cathode end, no marking on bi-directional types maximum ratings (ta = 25 c unless otherwise noted) parameter peak pulse power dissipation with a 10/1000 us waveform '1' (fig. 1) peak pulse current with a 10/1000 us waveform (1) (fig. 3) power dissipation on infinite heatsink at tl = 75 c (fig. 8) peak forward surge current 8.3 ms single half sine-wave uni-directional only '2* maximum instantaneous forward voltage at 100 a (or uni-directional only operating junction and storage temperature range symbol pppm 'ppm pd 'fsm vf tj. tstg limit 1500 see next table 6.5 200 3.5 -55to + 175 unit w a w a v ?c notes ''' non-repetitive current pulse, per fig. 3 and derated above ta = 25 c per fig. 2 '2' 8.3 ms single half sine-wave, duty cycle = 4 pulses per minute maximum n.i .semi-c ('dilution reserves the right to change lest conditions, parameter limits und package dimensions without notice information lumuhed by nj scmi-cunducton is believed to he htilh accurate and reliable m the lime of going to press. however ' scini-t oiidutiiirs iv-uincs mi reiptmsibilify tnr my errors ?r uirmsitmi discovered in its u.se nj semi-loiidiiitit* en ir.ti ii'its hi vcrilv ih.it il.'ila^htcij ire current hefbre plnciim urden
electrical characteristics (jedec registered data) (ta = 25 c unless otherwise noted) jedec type number general semiconductor part number stand-off voltage vwm (v) minimum breakdown voltage at 1.0m a vbr (v) maximum reverse leakage atvwm "d (ma) maximum clamping voltage atipp = 1.0 a vc(v) maximum clamping voltage at lpp = 10 a vc(v) maximum peak pulse current ipp (a) uni-directional types 1N6373(2) 1n6374 1n6375 1n6376 1n6377 1n6378 icte5 (2) icte8 icte10 icte12 icte15 icte18 5.0 8.0 10.0 12.0 15.0 18.0 6.0 9.4 11.7 14.1 17.6 21.2 300 25.0 2.0 2.0 2.0 2,0 7.1 11.3 13.7 16.1 20.1 24.2 7.5 11.5 14.1 16.5 20.6 25.2 160 100 90 70 60 50 bi-directional types 1n6382 1n6383 1n6384 1n6385 1 n6386 icte8c icte10c icte12c icte15c icte18c 8.0 10.0 12.0 15.0 18.0 9.4 11.7 14.1 17.6 21.2 50.0 2.0 2.0 2.0 2.0 11.4 14.1 16.7 20.8 24.8 11.6 14.5 17.1 21.4 25.5 100 90 70 60 50 notes '1| "c" suffix indicates bi-directional (2) icte5 and 1N6373 are not available as bi-directional (3' clamping factor: 1.33 at full rated power; 1.20 at 50 % rated power; clamping factor: the ratio of the actual vc (clamping voltage) to the vbr (breakdown voltage) as measured on a specific device ordering information (example) preferred p/n icte5-e3/54 icte5he3/54(1> unit weight (g) 0.968 0.968 preferred package code 54 54 base quantity 1400 1400 delivery mode 1 3" diameter paper tape and reel 1 3" diameter paper tape and reel note (1) automotive grade package outline dimensions in inches (millimeters) case style 1.5ke 0.210 (5.3) 0.190 (4.8) dia. 0.042(1.07) 0.038 (0.96) dia. 1.0(25.4) min. 0.375 (9.5) 0.285 (7.2) 1.0 (25.4) min.
|
